TECHNICAL SPECIFICATIONS
100 Series

. . . Email us at info@mech-tronics.com

Module Kits

 
  • Quick, Accurate Assembly
  • Four Side Accessibility
  • Six Standard Widths
  
  • Pre-drilled and tapped P.C. Board Mounting Holes
  • Optional Chassis Available

GENERAL DESCRIPTION

The Mech-Tronics Nuclear 100 Series Module Kits provide the experimenter with the ability to package his special instrumentation in accordance with the AEC TID-20893 recommendations for nuclear instrument standardization.

Stock Module Kits from 1 width to 6 widths are available as Model 101 thru 106 repectively.

A complete connector kit containing AEC Standard connector block, hood, all mounting hardware and 10 pins with 12" crimped leads is available as Model 100-10 Connector Kit.

 

PARTS LIST

 
Part Qty Description
1.1 1 Front Panel
1.2 1 Rear Panel
1.3 2 Perforated Panels
1.4 1 Right Side Panel
1.5 1 Left Side Panel
1.6 2 Extruded Rail
1.7 2 Square Rail
1.8.1 4 4-40 x 3/8" Oval Head Screw
1.8.2 4 4-40 x 3/8" Flat Head Screw
1.8.3 8 4-40 x 3/16" Flat Head Screw
1.9 2 Fasteners
100.gif (32301 bytes)

Click here for a 560 x 353 pixel
32K GIF Image

ASSEMBLY INSTRUCTIONS

  1. The face of the front panel is the side with the four countersunk screw holes. Using the oval head 3/8" screws, mount the extruded railing to the top and bottom of the right hand edge. The side of the extrusion with the slot should face inward.
  2. The 1/4" bar railing should then be mounted to the top and bottom of the left edge. You will note that one side of the bar railing has countersunk drilled and tapped holes - these should face outward.
  3. The rear panel may now be attached using the flathead 3/8" screws.
  4. The perforated top and bottom slide into the slot in the inside face of the extruded railing. These pieces are held in place by the left side cover. The parts are secured by four 3/16" screws.
  5. The right side cover fits between the two extruded railings and is secured by four flat head 3/16" screws.
  6. You will find the location of the pre-drilled and tapped holes on the extruded railing most convenient for mounting printed circuit boards or components. There is sufficient clearance, in most cases, to mount the board directly to the railings.
NOTE: An optional aluminum chassis provides a convenient method of mounting connectors for boards or components too heavy for printed circuit boards. The optional chassis fits between the lower extruded railings and the lower 1/4" bar railing. The flange fits over the drilled and tapped holes on the bar stock. The opposite side fits on the inside ledge of the extruded railing. Mounting screws are provided. Specify chassis by Module Kit Model No. followed by: -08. Example:  103-08 describes chassis for 3 wide module kit.

ACCEESORIES

A complete connector kit containing AEC Standard connector block, hood, all mounting hardware and 10 pins with 12" crimped leads is available as Model 100-10 Connector Kit.

Ordering Information:
Ordering Stock No. Shipping Weight
000101-00 2 lbs.
000102-00 2 lbs.
000103-00 3 lbs.
000104-00 3 lbs.
000105-00 4 lbs.
000106-00 4 lbs.

LINKS . . .

Product Listing PRODUCTS

Model 150 NIM Bins

 SPECS

Mech-Tronics   Nuclear Division
1635 N. 25th Avenue   (708) 344-0202
Melrose Park, IL  60160    
(708) 344-9823  Fax (708) 344-0067    

A leader in Precision Metal Fabrication | Photo Chemical Etching
Aluminum Dip Brazing | Nuclear Instrumentation

Email us at info@mech-tronics.com
Return to Mech-Tronics Services Page.
Return to Mech-Tronics Home Page.

Copyright © 1998 Mech-Tronics, All Rights Reserved